An inhomogeneous and complex concept that includes several factors is traction. This parameter must be at the highest level in order for the device to work stably. The way the energy is generated and the fuel burns is influenced by the normative deviation of the traction force indicators. Most often, owners of solid fuel boilers face such a problem if violations are observed in the installation work. Prudent people along with the equipment acquire a traction control in order not to encounter such a problem.
How to install the draft regulator on the boiler
The thermostat is one of the most important elements in the draft regulator. It is located inside the cylindrical body, it has a mechanical connection with the lever and chain. The thermostat has the form of a sealed flask, inside it is a heat-sensitive liquid that expands during heating. The element is located directly on the side that is in contact with the equipment.
What you need to install
To install the draft regulator in a solid fuel boiler, you will need:
- homemade or purchased traction control;
- solid fuel equipment;
- instruments;
- self-tapping screws.
Controller installation diagram
The regulator is connected to the fitting in the boiler by internal and external threads. A special sealant is used to seal the threads. Depending on where the rod tip is directed, the device is installed.
A shipping pipe made of plastic is removed from the equipment. In its place, the front side is installed hexagonal lever. There should be no hole in it. When tightening the screw when fixing the rod, make sure that its shoulder is close to the horizontally located hexagon, and the opposite end should be located above the chain of the boiler door. A large hook is inserted into the hole of the regulator lever, which is fixedly connected to the chain. The free hook should connect the remaining end of the chain. After that, it is checked (by turning the button) whether the lever and chain move freely. If you install the regulator horizontally, you need to align it on a white scale. They are guided by the red scale when installing the device in other positions.
Important! It is necessary to install the device exactly as it is written in the instructions, there should be no middle solution in any case.
How to adjust the controller after installation
In order to properly configure the device after installation, you must exactly follow the step-by-step instructions:
- Open the boiler door and do not close it with a chain. This is done in order to let in air.
- The locking screw on the adjustment knob loosens.
- The handle is inserted at the required temperature, for example, 650WITH.
- A thermometer is monitored on a solid fuel boiler after the mark reaches 650C It is necessary to connect the chain wire to the shutter. The main thing is not to completely close the damper. It should always be ajar for a couple of millimeters.
- The locking screw is tightened.
Important! The chain has free play, but it should not exceed 1 mm.
After that, the device is checked in all modes, even at the maximum. The main thing to remember is that time must pass between checks, since the solid fuel boiler heats up and does not always have time to cool down. To obtain the most effective result, you need to wait a while, so that the temperature conditions do not go astray.
Coal or firewood fades out gradually, therefore, solid fuel thermogenerators need a little more time for cooling than other similar equipment.
How to choose a traction control
The modern market offers a large number of models of solid fuel boilers. But not all of them are equipped with automation. In such models, the sleeve is mounted directly into the heat exchanger. Such boilers must be equipped with a draft regulator.
In order to correctly choose a mechanical traction device, you must adhere to the following instructions:
- To successfully raise the leaf, it is necessary that its weight and the capacity of the thermostat correspond.
- The temperature range should be between 60-800WITH.
- The lever must have an angle of rotation such that it is enough to completely close and open the sash.
- The threads in the boiler and draft regulator must match each other so that they can be connected.
Attention! The sleeve on the equipment can be located on the top or side, so it is very important to choose a regulator with the correct operating mode. Models have been developed in which work can be done in any position.
Hardware Features
In a solid fuel boiler, temperature plays a very important role, therefore a temperature regulator is needed. Such equipment is equipped with a water jacket. In order for the water in the unit to not boil, it is necessary to mount an automatic or mechanical draft regulator in it.
If water boils in such equipment, then it can explode, as there is an increase in pressure. When establishing a mechanical regulator, you will have to constantly monitor it. If you install automatic equipment on a solid fuel boiler, then human intervention is not required.
Leave Your Comment