How to lay a carpet

Carpet - quite a popular and common material among the types of flooring. In appearance, it resembles an ordinary carpet, but is easier to care for. You can install the carpet yourself using one of several simple methods.

Ways to properly install carpet

The service life of a material depends not only on its quality. Of great importance is the selected installation option.

Existing methods:

  1. Double-sided tape. It is one of the easiest options. It allows you to consolidate coverage at the minimum cost of finance and time.
  2. Glue. Suitable for concrete or wood floors. For work, use a special solution on which carpet is applied.
  3. Stretching Belongs to one of the most difficult methods. For the installation procedure, special equipment will be required. For fastening, gripper rails installed around the perimeter of the room are used. The floor covering is attached to them.

REFERENCE! Many users mount the carpet directly under the baseboards. This method is one of the most ineffective, since the material cannot be strongly exposed to furniture or laid in rooms with high traffic. The advantage is the ability to quickly dismantle.

Any floor covering during installation requires a special substrate. Carpet in this case is no exception. Any material is suitable as a substrate. Experts recommend staying on elastic and flexible textures. The best choice would be synthetic felt or a rubber layer. Polyurethane foam is also suitable.

ATTENTION!When laying on concrete floors, the presence of an additional layer is mandatory. Wood retains heat better, therefore, in this case, the presence of a substrate can be discarded.

An important stage in the repair work is the preparatory process. The laying base must be clean and dry. A prerequisite is a flat floor surface.

If dents or bumps are present, the surface must be leveled. For concrete floors, a special mixture for leveling is suitable. The wooden base can be upholstered with plywood sheets or chipboard. Special attention when leveling the floor of the tree should be given to nails. They must be driven as much as possible into the leveling coating so that the caps do not stick out. Otherwise, damage may occur on the underside of the coating.

REFERENCE!If there are skirting boards in the room, they should be completely removed.

Antiseptic and water repellent treatment is mandatory. This will help prevent excess moisture, mildew or mildew. For work, special solutions are suitable, which can be purchased at the building materials store.

If you plan to put the carpet with adhesive or tape, the floor must be primed. This item is optional, but the presence of a primer improves adhesion to the floor and significantly increases the life of the carpet.

ATTENTION!To remove small protrusions or cracks, grinding over the entire surface is suitable. A mixture for leveling concrete in this case is not needed.

How to lay a carpet with your own hands

After preparing the necessary tools and the floor itself, you can begin to work. A day before laying, it is recommended to carefully spread the carpet and leave it so that it is completely straightened. This will help prevent bends, dents and breaks on the surface of the coating.

When laying, the material must be slightly overlapped with the walls. The coating itself should be carefully distributed on the surface so that after installation there are no bumps, and the carpet fits snugly on the floor. For cutting, a special breadboard knife is suitable. The material is cut strictly at the junction of the floor and the base of the wall. If two or more sheets are stacked, the material must be overlapped with each other. This will help form the right joints.

When attaching with adhesive tape, laying is carried out in two stages. The carpet folds in half, freeing part of the room. Segments of adhesive tape are glued on the freed perimeter, the protective film is removed. Starting from the center, the carpet is attached to the material. A similar procedure is carried out on the other hand.

When choosing glue, similar actions are carried out. Part of the area of ​​the premises is exempt from coverage. The glue is applied using a notched trowel. After treatment, the composition should be kept for about 5-10 minutes. After unfolding on the adhesive surface, the carpet must be carefully smoothed.

Plinths should be installed at the junction of walls and floor. They will hide the corners of the flooring and help in additional fixation. After a few simple steps, the self-laying of the carpet is finished.

Carpet as an additional floor covering helps to make the room more comfortable, and also provides additional thermal effect. The features of the canvas are easier care and simple steps when laying. A few recommendations will help in independent work on laying the material.

Watch the video: An easy way of installing carpet in your bedroom with 3 easy to tools (March 2024).

Leave Your Comment